|
|
|
|
Search Hartville Tool
Bandsaw Accessories |
[«] « prev | 1 | 2 3 4 5 6 7 | next » [»] 121 Total Results
Showing Results from 1 to 20
|  Kreg Bandsaw Fence
Designed with the assistance of noted band saw expert Mark Duginske, this fence brings an unprecedented level of rigidity, adjustability, and precision to band saw operation. It’s quality and performance easily exceed just about any OEM fence available. The fence is adjustable in two dimensions, both vertically and horizontally, for ease in setting it parallel to the blade.
The optional Micro-Adjuster (see inset photo) lets you dial in very precise fence positions. It attaches to the mounting rail of the saw and threads into the clamping block. Cutting accuracy and repeatability is further enhanced by the precision lens curser that reads off of the included scale. Simply set the cursor close to the desired cut, lock down the micro-adjuster knob, and fine-tune the cut by rolling the thumbwheel.
The optional Re-saw Guides allow drift angle adjustments to be made on the fly while cutting. The 4-1/2” Guide is the standard size for most 14" band saws. The 7" Guide is for saws that have riser block extensions. Mounts to most 14” inch band saws including Jet, Delta, General, Grizzly, and many others. USA
*NOTE: This update of the the former Fasttrack fence will accept the 4" and 7" Fasttrack Re-Saw Attachments (#10592 & 10595), however the Micro-Adjusters are not interchangeable.
|  Carter Electronic Tension Gauge
Band saw blade tensioning is one of the most critical aspects of maintaining cutting accuracy and consistent performance. Until now, there has been no way to quickly and accurately monitor and maintain optimum tension. The Carter Electronic Tension Gauge (ETG) is a unique device that easily sets exactly the right tension for any size blade.
Proper tension means better cutting and longer life of blades and machine components. It provides continuous, highly visible electronic readout, including full blade tension
information, even when cutting. Safety circuit cuts power to saw if the blade loses tension. Unit fits 14" Delta and Jet. USA
|  The Bandsaw Book
It is the unfortunate truth that the versatile band saw is probably the most under-appreciated and under-utilized tool in most shops. Fortunately, author Lonnie Bird has put together a comprehensive reference filled with valuable advice on choosing a band saw, tune-up tips, sawing techniques, and super jigs.
This book will have you using your band saw a lot more often and doing things you may not have thought possible. Includes 3 beautiful skill building projects - a simple but elegant mitered box, and superb reproductions of an 18th century Tea Caddy and a Connecticut Tea Table. Approx. 200 pages with over 225 color photos and illustrations. Soft cover. USA
|  45/90 Brass Angle Block
Made to our specifications, this beautiful and highly precise, solid brass angle block will find quite a few uses around the shop. A substantial 3/8" thick, it easily stands on any flat surface. Most importantly, it is accurate to within + or - 0.001" over the length of each side. Set table saw blade or jointer fences to a perfect 90 degrees, be sure band saw or drill press tables are square to the blade or bit, or even use it to check try squares. Block is approx. 2-7/8" high. Super accessory for our X-Point Power Tool Gauge (#78401). India
|  93-1/2" x 1/8" x 14tpi (reg)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 93-1/2" x 3/16" x 10tpi (reg)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 93-1/2" x 1/4" x 6tpi(reg)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 93-1/2" x 3/8" x 4tpi (skip)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 93-1/2" x 5/8" x 3tpi (hook)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 105" x 1/8" x 14tpi (reg)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 105" x 3/16" x 10tpi (reg)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 105" x 1/4" x 6tpi (reg)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 105" x 3/8" x 4tpi (skip)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
| 105" x 5/8" x 3tpi (hook)
The performance and longer life of Olson All Pro band saw blades more than make up for the extra cost. The Super Hard Edge (Rc 64-66) is achieved by a greater concentration of pin-point carbide in the material. This carbide structure allows the teeth to obtain a higher Rockwell hardness, increasing edge retention and durability. The Tempered Back (Rc 40-50) provides more accurate cuts, less twist, and less back deformation. Teeth are precision milled (not stamped), and set for optimum performance. The 5/8" blade cuts a much thinner kerf (.045") than a typical 5/8" or 3/4" blade. It is highly recommended for re-sawing due to its superior tracking and handling ability. All blades .025" thick. Cut wood, plastic, and non-ferrous metals. USA
|  Saw Blade Lube
Compounded to keep band saw, scroll saw, coping saw, and other saw blades from clogging with chips or pitch. Prolongs blade life, and produces smoother, quieter cuts. 8" x 1" stick. USA
|  Set of 3 Delta Inserts (Delta 14" & Most 14" Imports)
These semi-rigid, snap-in plastic inserts are an inexpensive way to replace the chewed-up throat plate on your band saw. Can be custom cut to match blade size, and will reduce splintering and tear-out. Unlike metal inserts, these won't dull saw teeth if you happen to nick them. Delta inserts are 2-1/2" (OAD - Overall Diameter) x 2-3/16" (to lip), Jet inserts are 2-1/2" x 1-3/4". USA
| Set of 3 Jet Inserts ( Jet 12", 14" & 18")
These semi-rigid, snap-in plastic inserts are an inexpensive way to replace the chewed-up throat plate on your band saw. Can be custom cut to match blade size, and will reduce splintering and tear-out. Unlike metal inserts, these won't dull saw teeth if you happen to nick them. Delta inserts are 2-1/2" (OAD - Overall Diameter) x 2-3/16" (to lip), Jet inserts are 2-1/2" x 1-3/4". USA
|  X-Point Power Tool Set-Up Gauge
Imagine every blade running true; every fence lining up perfectly; every angle set exactly; every machine cutting smoothly, quietly, and with perfect accuracy. With the Redline X-Point Power Tool Set-Up Gauge it's no dream.
This precise, professional quality measuring instrument is designed to provide power tool setup readings to within 0.001". It eliminates performance robbing set-up problems that would be nearly invisible to the naked eye. With the X-Point you'll soon find your table saw, band saw, jointer, and drill press more accurate and more enjoyable to use than ever before. Use it to set the heel & toe of table saw blades; check table saw miter slot and fence alignments; set blade, fence, and miter gauge angles; check for arbor or spindle run-out; set jointer blades; or even check your shop squares to see just how square they are. Once you have it you'll be sure to find even more uses.
The 3 point adjustable bearing system allows you to move the gauge in the miter gauge slot without slop or loss of accuracy. The base of the gauge also contains 2 powerful rare earth magnets, so it stays put when using it on jointer beds or drill press tables. Brass Angle Block (#85883) is optional, but helpful. Set includes base, dial indicator, instruction manual and protective molded plastic case. Solid aluminum anodized body. China
|  Band Saw Quick-Crank
The OEM adjustment on the bandsaw is tough to get your hands around, and you can't ever give it a full turn. Quik-Crank puts the adjustment above the saw for faster blade changing and tensioning. Includes threaded extension rod and a speedy crank style adjusting knob. Installs in about 15 min. Fits most 14" Delta, Jet, Powermatic, Grizzly, Sears, Reliant & Rigid, plus 12" Jet bandsaws. USA
|  Bandsaw Fence
A pleasure to use, a snap to install, and better than any OEM fence you'll find. The rail adapter plate bolts directly to the pre-drilled holes you'll find on your Delta or Taiwanese saw. Slip rail & fence on and you're in business! Fence and rail are both 18" long. Primarily for 14" bandsaws, but may be adapted to other sizes. Save valuable lumber, or cut whisker thin laminates. Annodized aluminum. USA
NOTE: Re-Saw Guides only available. Re-saw guides compatible with Kreg Bandsaw Fence (#52664).
|
[«] « prev | 1 | 2 3 4 5 6 7 | next » [»] 121 Total Results
Showing Results from 1 to 20
|
|
|
| |
|
|
|
|
|
|
|