Search Hartville Tool
Router Bits -- Laminate Trim Bits
|
|
|
[«] « prev | 1 | 2 | next » [»] 26 Total Results
Showing Results from 1 to 20
|
 1/2" D x 1-1/2" CL x 4-1/4" OAL Up/Down Combo
State-of-the-art, double flute, spiral flush trim bits make extra smooth cuts in difficult materials and tricky application problems. The Up/Down uses a double ball bearing guide and is made for trimming double sided laminates or veneers. Solid Carbide. Made by Whiteside. USA
|
1/2" D x 1-1/4" CL x 3-3/4" OAL Upcut
State-of-the-art, double flute, spiral flush trim bits make extra smooth cuts in difficult materials and tricky application problems. Double ball bearing guide. Choose from Up Cut (RRFT5125 & RRFT5200) or Down Cut (RRFTD5125 & RRFT5200). Solid Carbide. Made by Whiteside. USA
|
1/2" D x 1-1/4" CL x 3-3/4" SH Downcut
State-of-the-art, double flute, spiral flush trim bits make extra smooth cuts in difficult materials and tricky application problems. Double ball bearing guide. Choose from Up Cut (RRFT5125 & RRFT5200) or Down Cut (RRFTD5125 & RRFT5200). Solid Carbide. Made by Whiteside. USA
|
1/2" D x 2" CL x 4-3/4" OAL Upcut
State-of-the-art, double flute, spiral flush trim bits make extra smooth cuts in difficult materials and tricky application problems. Double ball bearing guide. Choose from Up Cut (RRFT5125 & RRFT5200) or Down Cut (RRFTD5125 & RRFT5200). Solid Carbide. Made by Whiteside. USA
|
1/2" D x 2" CL x 4-3/4" OAL Downcut
State-of-the-art, double flute, spiral flush trim bits make extra smooth cuts in difficult materials and tricky application problems. Double ball bearing guide. Choose from Up Cut (RRFT5125 & RRFT5200) or Down Cut (RRFTD5125 & RRFT5200). Solid Carbide. Made by Whiteside. USA
|
 1/16" R X 1/8" D X 1/4" CL X 2" OAL
For veining details, flutes, plate grooves, pen and pencil slots, drawer pulls, this is the type of bit to use. #RSC39, #RSC40, and #RSC41 are solid carbide are also known as Round Veining bits. All other bits carbide tipped. 2 flute. Made by Whiteside. USA
|
3/32" R X 3/16" D X 3/8" CL X 2" OAL
For veining details, flutes, plate grooves, pen and pencil slots, drawer pulls, this is the type of bit to use. #RSC39, #RSC40, and #RSC41 are solid carbide are also known as Round Veining bits. All other bits carbide tipped. 2 flute. Made by Whiteside. USA
|
1/8" R X 1/4" D X 1/2" CL X 2" OAL
For veining details, flutes, plate grooves, pen and pencil slots, drawer pulls, this is the type of bit to use. #RSC39, #RSC40, and #RSC41 are solid carbide are also known as Round Veining bits. All other bits carbide tipped. 2 flute. Made by Whiteside. USA
|
 FLAT VEINING - 1/8" D X 1/4" CL X 2" OAL
Cuts dados in laminate or veneered materials. No pilot. For use on routers or trimmers equipped with a guide fence or template guide bushing. Double flute for smoother cuts. Bits are solid carbide. 1/4" shank. Made by Whiteside. USA
NOTE: Bits below run flat bottom grooves only.
|
FLAT VEINING BIT - 3/16" D X 3/8" CL X 2" OAL
Cuts dados in laminate or veneered materials. No pilot. For use on routers or trimmers equipped with a guide fence or template guide bushing. Double flute for smoother cuts. Bits are solid carbide. 1/4" shank. Made by Whiteside. USA
NOTE: Bits below run flat bottom grooves only.
|
FLAT VEINING BIT - 1/4" D X 1/2" X 2" OAL
Cuts dados in laminate or veneered materials. No pilot. For use on routers or trimmers equipped with a guide fence or template guide bushing. Double flute for smoother cuts. Bits are solid carbide. 1/4" shank. Made by Whiteside. USA
NOTE: Bits below run flat bottom grooves only.
|
 HOLE & FLUSH TRIM BIT - 1/4" D X 1/4" CL X 2" OAL
This solid carbide has bit has a plunge point to bore its own pilot hole. The self-contained pilot guides the bit in pattern cutting. Especially good for cutting laminate covered solid surface materials, drywall, plywood, and other construction materials. 1/4" shank. Made by Whiteside. USA
|
 FLUSH & 7 DEG. BEVEL TRIM BIT - 1/4" D X 3/8" CL X 1-1/2" OAL
Solid carbide bit for trimming of laminates. 7 degree bevel trim. No pilot. For use on routers or trimmers equipped with a guide fence or template guide bushing. 1/4" shank. Made by Whiteside. USA
|
 7 DEG. BEVEL TRIM BIT X 1/4" D X 1/4" CL X 2" OAL
Solid carbide bit for trimming of laminates. 7 degree bevel trim. Double ended for twice the life. Self-contained no-maintenance solid pilot. 1/4" shank. Made by Whiteside. USA
|
 7 DEG. BEVEL TRIM BIT - 1/4" D X 1/4" CL X 1-1/2" OAL
Solid carbide bit for trimming of laminates. 7 degree bevel trim. Self-contained no-maintenance solid pilot. 1/4" shank. Made by Whiteside. USA
|
 DADO TRIM BIT - 1/4" D X 1/4" CL X 1-1/2" OAL
Designed for flush trimming of laminates inside shallow dados. 1/8" long, self-contained, no-maintenance solid pilot. 1/4" shank. Made by Whiteside. USA
|
 FLUSH TRIM BIT - 1/4" D x 3/8" CL X 1-1/2" OAL
Solid carbide bit for flush trimming of laminates. Cutting surface is a full 1/8" longer than standard trimmers. Self-contained no-maintenance solid pilot. 1/4" shank. Made by Whiteside. USA
|
 FLUSH TRIM BIT - 1/4" D x 3/8" CL X 1-1/2" OAL
Solid carbide bit for flush trimming of laminates. Cutting surface is a full 1/8" longer than standard trimmers. Self-contained no-maintenance solid pilot. 1/4" shank. Made by Whiteside. USA
|
 1/2" D X 1/4" CL X 1-5/8" OAL - 1/4" SHANK
Why a square bearing? With normal round bearings glue and residue from applied laminates build up on the bearing with every revolution. With a square bearing, that build-up is all but eliminated since the bearing stops spinning as soon as it touches the work. Then the flat side slides along the work piece edge. Plus, the bearing is made with non-stick Teflon, so the bearing won't mark your work, and any residue that does accumulate is easily cleaned off.
Bits are designed with a slight taper on the cutting diameter. This allows up and down adjustments to achieve an exact blend - even after re-sharpening. R2640 is 1/4" shank. R2660 is 1/2" shank. 2 flute. Carbide tipped. Made by Whiteside. USA
|
3/4" D X 5/8" X 2-1/4" OAL - 1/2" SHANK
Why a square bearing? With normal round bearings glue and residue from applied laminates build up on the bearing with every revolution. With a square bearing, that build-up is all but eliminated since the bearing stops spinning as soon as it touches the work. Then the flat side slides along the work piece edge. Plus, the bearing is made with non-stick Teflon, so the bearing won't mark your work, and any residue that does accumulate is easily cleaned off.
Bits are designed with a slight taper on the cutting diameter. This allows up and down adjustments to achieve an exact blend - even after re-sharpening. R2640 is 1/4" shank. R2660 is 1/2" shank. 2 flute. Carbide tipped. Made by Whiteside. USA
|
[«] « prev | 1 | 2 | next » [»] 26 Total Results
Showing Results from 1 to 20
|