From ShopNotes, Woodsmith and Workbench Magazines

SHOPNOTES: Portable Assembly Station

Sometimes an extra worksurface comes in handy around the shop. So I came up with a simple table that knocks down in seconds. And it's perfect as an outside or jobsite bench, too. To see how it's built, click the following link: Continue reading SHOPNOTES: Portable...

WOODSMITH: Band Clamp Corner Protection

Every shop should have a few band clamps. Here's a simple tip that will allow you to use them more effectively. Just click the following link and take a look: Continue reading WOODSMITH: Band Clamp Corner Protection

SHOPNOTES: Chamfer Plane

My block plane is always close by when I'm in the shop. One job it's often used for is quickly softening a corner with a chamfer. So I came up with a simple add-on that helps me get consistent results every time. To see how it works, click the following link: Continue reading...

WOODSMITH: Invisible Finish Repair

Unfortunately, being careful during use isn't a guarantee, and inevitably, a project is going to end with a scratch or two in the finish. But rather than give in, I came up with an easy way to fix them. Click the following link and take a look: Continue reading WOODSMITH: Invisible...

SHOPNOTES: Fold-up Router Table

A router table can help you get more from your router, but a dedicated router table can take up valuable space. Here's a version that works great, and can quickly and easily be stored out of the way. To see it, click the following link: Continue reading SHOPNOTES: Fold-up Router...

WOODSMITH: Putty Trick

Filling nail holes with wood putty can often result in a mess. I came up with a much tidier way to get the job done. Just click the following link and take a look: Continue reading WOODSMITH: Putty Trick

SHOPNOTES: Dowel Drilling Jig

Drilling a centered hole in the end of a dowel presents a few challenges. But I've come up with a simple technique that makes it a snap. To see how it works, click the following link: Continue reading SHOPNOTES: Dowel Drilling Jig

WOODSMITH: Flush Cut Shield

A properly installed wood plug can make a screw hole disappear. Here's a tip that will help ensure the job goes smoothly and turns out right. Just click the following link: Continue reading WOODSMITH: Flush Cut Shield

SHOPNOTES: Drill Press Table Upgrade

It's no secret that the metal table on a drill press isn't suitable for woodworking. But with a couple hours in your shop, you can give it a facelift. To see how, click the following link: Continue reading SHOPNOTES: Drill Press Table Upgrade

WOODSMITH: A Lipped Box Lid

Making a box with a snug-fitting, lipped lid is a real accomplishment. Let me show you a trick that will guarantee a great result. Just click the following link: Continue reading WOODSMITH: A Lipped Box Lid

SHOPNOTES: Micro-Adjust Your Router Table Fence

My router table fence is an accurate, reliable part of my router table. My only gripe was how difficult it was to make fine adjustments. So I came up with a simple solution that doesn't take a lot of time or material. To see how it works, click the following link: Continue reading...

WOODSMITH: Sanding Disc Alignment Tool

If you can find a way to make basic shop tasks go a little easier, you can concentrate on more important things. To that end, check out this simple, time-saving tip. Just click the following link: Continue reading WOODSMITH: Sanding Disc Alignment Tool

SHOPNOTES: Telescoping Drawer Gauge

It can be a little tricky measuring for and sizing a drawer bottom. Thankfully, this handy tool eliminates the measuring altogether and guarantees the right size. To see how it works, click the following link: Continue reading SHOPNOTES: Telescoping Drawer Gauge

WOODSMITH: Magnetic Stop Block

A stop block clamped to the rip fence of your table saw makes cutting identical short pieces easier and safer. But even a simple stop block can be improved. Click the following link and take a look: Continue reading WOODSMITH: Magnetic Stop Block

SHOPNOTES: Small Parts Clamp

Assembling small projects can be a challenge with full-size woodworking clamps. Instead, I've come up with a compact assembly station that applies just the right amount of pressure. To see how it works, click the following link: Continue reading SHOPNOTES: Small Parts Clamp