|
Lid Supports from Rockler
|
|
|
Adjustable Lid Support This is the lid support for a variety of applications! It is convertible since it can be installed on either horizontal or vertical, for lids or drop fronts. It is reversible to be mounted left or right, and change tension direction from lift-up to drop-down as needed.It's adjustable: Tension adjustment can be made easily using a number 4 Allen wre . . .
|
Mini Concealed Soss Hinge 3/8' Wide x 1' Long. For 1/2'-thick material.Price per pair. . . .
|
Solid Brass SmallBox Cylinder Hinges Solid brass hinge for those small jewelry or pencil boxes. Installation requires cutting a 45 degree bevel and drilling 5mm holes. Hinge is 15mm (9/16") long overall x 5mm (3/16") diameter. 10 per pack. . . .
|
Solid Brass SmallBox Hinge The full mortise hinge provides a built-in stop, allowing a lid to remain open at about 95°. For use when an additional stay is not desired.The hinge is mortised flat into the box and lid. . . .
|
Solid brass Jewelry Box Stop Hinges . . .
|
Jewelry Box Tray Support Lifts and lowers the jewelry box tray when lid opens and closes. By lifting the top tray, the support provides access to the jewelry below. Measures 7' long overall. Use with a 95 stop hinge. Solid Brass. Price per pair. . . .
|
Jewelry Box Lid Support Cut a mortise 1/4' wide x 2-7/8' long x 1/2' deep to install. Solid brass. . . .
|
Jewelry Box Tray Support Lifts and lowers the jewelry box tray when lid opens and closes. By lifting the top tray, the support provides access to the jewelry below. Measures 7' long overall. Use with a 95 stop hinge. Solid Brass. Price per pair. . . .
|
Solid Brass Quadrant Hinge Hinge measures 1' x 1' x 1-1/4' overall. Requires an additional 1-1/4' deep mortise for the support arm. Use with a minimum of 3/8' thick material. price per pair. . . .
|
Solid Brass Small Box Hinges . . .
|
HeavyDuty Soft Down Lid Support With a range of 60-86' /pound per support and 121-173' /pound per pair (formula: lid wt. x front-to-back size ÷ 2 =' /pounds), these heavy-duty supports offer the security of gentle descent for larger applications. Opening to 70º, they are ideal for both overlay and inset lids. Requires 5-1/8' x 7/8' x 10-3/4' for mounting. Overall dimensions are 5 . . .
|
Trunk Lid Support Plated steel support measures 6-7/16' center to center and 6-7/8' long overall. 7/16' wide. Screws included.Price per pair. . . .
|
Briefcase Support Reversible support. 3-3/4' center to center. 4-3/16' overall. Price for each. . . .
|
Trunk Strap Hinges Made from stamped steel and then plated for decorative appeal. 90 stop hinges. Price per pair. . . .
|
90 Stop Hinges . . .
|
Case Catch Catch has an attractive profile. 1-1/4' Wide x 1-5/8' H. Comes in either brass plated or nickel plated finish. Price per pair. . . .
|
Classic Oblong Catch Quality catches with the traditional shape used on many trunks and chests. Small catch- 1-1/2' W x 2-3/4' H- 2 per pack. . . .
|
Classic Oblong Catches . . .
|
Locking Drawbolt This fine brass plated drawbolt locks easily with a turn of a key. The lock is stamped steel with brass plating. Heavy duty. Keyed alike and supplied with one key (#151).1-3/4' W x 3-3/8' L Overall 5/8' projection.Comes with #4 X 3/4' oval head screws for mounting. Surface mounted. . . .
|
Catch with Padlock Hasp Plated steel. 2 per pack. . . .
|
Spring Trunk Lock Beautiful lock! The hasp opens to 135°. 3-3/4' wide x 4- 13/16' high. Brass plated. . . .
|
Figure 8 Trunk Lock Coordinate with matching corners. 3-3/4' W x 6-5/8' H. Surface mounted. Price for each. . . .
|
Basic Economy Drop Front Support . . .
|
Trunk Lid Support Plated steel support measures 6-7/16' center to center and 6-7/8' long overall. 7/16' wide. Screws included.Price per pair. . . .
|
Cedar Chest Hinge and Lid Support This time tested classic design has been used on cedar chests and hope chests for many years. Sturdily constructed from brass plated steel. Mounts to side of case and underside of flat lid. Allows lid to open to approximately 95 degrees. Screws included.Price per pair. . . .
|
Lift Up Door Support To close, lift slightly and the support easily disengages. One support is required for small to medium doors. Nickel plated steel. 12' overall. . . .
|
Solid Brass Hardware Study construction. Solid brass with a polished, lacquered finish. Dual purpose lid support or drop front. (right and left hand are designated by drop front use as you face the desk). Overall length is 9-3/4' . Each arm is 4-7.8' long. . . .
|
Solid Brass Support Price for each support. . . .
|
Soft Down Support Compact design makes these supports ideal for installing in tight places. Use one support per 43' /lbs. Figure' /lbs with this formula: (lid wt. X front to back size) divided by 2. Price for each one. . . .
|
Soft down support Lids lower gently--never crushing fingers. Support opens lids to a maximum angle of 105 and is 8-7/8' long overall. They have nickel plated steel arms with cream colored plastic housing. Compact design makes these supports ideal for installing in tight places. Use one support per 43 inch/lbs. Figure inch/lbs with this formula: (lid wt. X front to b . . .
|
Self Balancing Lid Support Surface mounts only 4-1/2' from back of the cabinet. Statuary bronze finish. (Lid weight times front to back size) divided by 2 equals' pounds range. Use on toy boxes with 3/4' thick backs. Price per pair. . . .
|
Quiet Action Support Patented friction discs at the pivot point prevent lids from slamming shut. Lowering action is gentle and controlled. Supports lock when opened and unlock when closed. Smooth, friction free movement at any stopping point. Bronzed steel. . . .
|
Toy Box Lid Supports Prevents lids from accidentally slamming shut on fingers. Measures approximately 5' long pivot to pivot in extended position. Use this formula to choose your supports: (lid wt. times front to back size) divided by 2 = inch lbs range. Use on toy boxes with 3/4' thick backs. Statuary bronze finish. Price per individual lid support. . . .
|
Black Jewelry Box Turnbuttons . . .
|
Brass Jewelry Box Staple Hasp Catch . . .
|
Brass Jewelry Box Hook . . .
|
Brass Jewelry Box Handle . . .
|
Brass Jewelry Box DrawSnap Catch . . .
|
BrassPlated SmallBox Fastener Hinge . . .
|
BrassPlated LargeStrap SmallBox Fastener Hinge . . .
|
BrassPlated SmallBox Fastener Hinge . . .
|
BrassPlated SmallBox Fastener Hinge . . .
|
Solid Brass SmallBox Hinges . . .
|
BrassPlated SmallBox Fastener Hinge . . .
|
BrassPlated SmallBox Fastener Hinge . . .
|
BrassPlated SmallBox Fastener Hinge . . .
|
BrassPlated SmallBox Fastener Hinge . . .
|
BrassPlated SmallStrap SmallBox Fastener Hinge . . .
|
BrassPlated Mini Decorative SmallBox Fastener Hinge . . .
|
BrassPlated SmallBox Offset Spring KerfCut Hinge . . .
|
BrassPlated SmallBox Offset KerfCut Hinge . . .
|
BrassPlated SmallBox Spring KerfCut Hinge . . .
|
BrassPlated SmallBox Spring KerfCut Hinge . . .
|
BrassPlated SmallBox KerfCut Hinge . . .
|
BrassPlated SmallBox KerfCut Hinge . . .
|
Damper Gas Spring Kit Maximum door height 24"; minimum 10".Overall extended length is 9-1/4".Easy installation.Kit includes two dampers and four mounting brackets.Black.Screws not included. . . .
|
LiftOMatreg Gas Springs Minimum door height 10-1/2' Maximum door height 24". Set includes two gas springs and four mounting brackets. (Screws not included). Easy installation. Black. . . .
|
EasyLift Lid Support This support also holds lids at virtually any number of intermediate locations from 25 degrees to 90 degrees! Designed for lids between 19'and 26' long and weighing under 9 lbs. Most lids require only one support, but two can increase the weight capacity. Nylon body with steel springs. Zinc mounting brackets. Black. . . .
|