Delta Power from Rockler
Select Subcategory Here
 Delta Power
|
|
|
 DELTA AP400 1 HP 650 CFM Single Stage Dust Collector
Motor: 1 HP, 12/6 amp, 120/240V (wired 120V), 1 Phase motor, 60 hz, 3450 RPMMax. CFM: 650Max. Static Pressure: 8.5 in waterImpeller Diameter: -Filter Bag Area: 20 square feetStandard Bag Filtration: 30 MicronChip Bag Area: 2.6 cubic feetLength: 27" (686 mm)Width: 14" (356 mm)Height: 57" (1,448 mm)Weight: 90 lbs (41 kg)Warranty: 2 Year Warranty . . .
|
 DELTA 46715 14 CastIron Lathe
Motor: 3/4 HP, 120V, 1 Phase, 60 hz, 1725 RPMMotor Control: On/Off SwitchSpeed: 600-2200 RPMSwing over bed: 14" (356 mm)Swing Over Base: 10-1/8" (257 mm)Distance between Centers: 40" (1016 mm)Drive spindle thread count: 1" -8 RH threadDrive spindle through hole: 7/16" (11 mm)Head and tailstock taper: #2 MorseTailstock through hole: 3/8" (9.5 mm)Tai . . .
|
 DELTA 36L31XBC50 3 HP Left Tilt UNISAWreg with BIESEMEYERreg Fence
Motor: (TEFC) 3 HP, 230V , 60 hz, 1 phaseArbor Size: 5/8?? (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 4000 RPM (with 3450 RPM motor)Max Rip To Right Of Blade: 50" (1270 mm)Max Rip To Left Of Blade: 12" (305 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 16-13/ . . .
|
 DELTA 36R31XU50 3 HP Right Tilt UNISAWreg with UNIFENCEreg
Motor: (TEFC) 3 HP, 230V , 60 hz, 1 phaseArbor Size: 5/8?? (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 4000 RPM (with 3450 RPM motor)Max Rip To Right Of Blade: 50" (1270 mm)Max Rip To Left Of Blade: 12" (305 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 16-13/ . . .
|
 DELTA 15234 15 Production Drill Presses
Motor: 3 Phase, 3/4 HPMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and 3-Leg Overload Protection (LVC)Column Diameter: 2-3/4"(70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 . . .
|
 DELTA 36L53L 10 Unisawreg 5HP 3 Phase Left Tilt
Motor: 5 HP, 200/230/460V, 60 hz, 3 PhaseArbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 4000 RPM (with 3450 RPM motor)Max Rip To Right Of Blade: With UNIFENCE® Saw Guide or BIESEMEYER® Commercial Saw Fence system: 50" (1270 mm)Max Rip To Left Of Blade: With UNIFENCE®: 15-1/2" (394 mm) With BIESEMEYER® Fence: 12" (305 mm)Depth Of . . .
|
 DELTA 36980 10 Left Tilt CONTRACTORS SAWreg with DELTAreg T2 30 Fence Rail and Two CastIron Table
Motor: 1-1/2 HP, 115V/230V (wired 115V), 60 hzArbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 3000 RPMMax Rip To Right Of Blade: 30" (762 mm)Max Rip To Left Of Blade: 13-1/2" (343 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 17-1/2" (444 mm)Table . . .
|
 DELTA 15344 15 Production Drill Presses
Motor: 3 Phase, 3/4 HPMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and 3-Leg Overload Protection (LVC)Column Diameter: 2-3/4"(70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 . . .
|
 DELTA 22470 24 Planer 22470
Motor: 7-1/2 HP, 3 Phase, 220/440V (wired 220V), 60 hzMotor Control: 24V, low voltage controlMinimum Thickness Capacity: 11/64" (4 mm)Max. Width of Stock: 24" (610 mm)Max. Thickness of Stock: 8-5/8" (219 mm)Min. Length of Stock: 9" (229 mm)Number of Knives: 3Max. Depth of Cut: 3/16" max. (5 mm)Planing Width: 3/16" (5 mm)Cutterhead Diameter: 3-1/8" . . .
|
 DELTA 36R53L 10 Unisawreg 5HP 3 Phase Right Tilt
Motor: 5 HP, 200/230/460V, 60 hz, 3 PhaseArbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 4000 RPM (with 3450 RPM motor)Max Rip To Right Of Blade: With UNIFENCE® Saw Guide or BIESEMEYER® Commercial Saw Fence system: 50" (1270 mm)Max Rip To Left Of Blade: With UNIFENCE®: 15-1/2" (394 mm); with BIESEMEYER® Fence: 12" (305 mm)Depth Of . . .
|
 DELTA 50764 5 HP Dust Collector 4800 CFM
Motor: 5 HP, 3450 RPM, 230V/460V (Wired 230V), 3 phase, 60 HzMax. CFM: 4800Max. Static Pressure: 10.5 (inches of water)Impeller Diameter: 13.5" (343 mm)Filter Bag Area: 140.8 square feet, 13.08 square metersStandard Bag Filtration: 1 micronChip Bag Area: 12.4 cubic feet, 352 litersLength: 75" (1905 mm)Width: 26" (660 mm)Height: 110" (2794 mm)Weight . . .
|
 DELTA 15262 15 Production Drill Presses
Motor: 1 Phase, 3/4 HPMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and Overload Protection (LVC)Column Diameter: 2-3/4" (70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 x 356 . . .
|
 DELTA 33401 14 Radial Arm Saws
Motor: 5 HP, 3 Phase, 230/460V (wired 230V), 60 hz, 3450 RPM, TEFC (totally enclosed, fan cooled) motorMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and Overload Protection (LVC)Blade Diameter: 14Arbor Size: 1" (25 mm)Crosscut Capacity (1" depth of cut): 29" (737 mm)Miter at 45° R & L (1" depth of cut): 22" (559 mm)Depth Of . . .
|
 DELTA RS830 10 Professional Radial Arm Saw
Motor: 1-1/2 HP, 120/240V, (wired 120V), 1 Phase, 60 hzMotor Control: Blade Diameter: 10" (254 mm)Arbor Size: 5/8"Crosscut Capacity (1" depth of cut): 16" (406 mm)Miter at 45° R & L (1" depth of cut): L: 10-1/2" (267 mm) R: 11" (279 mm)Depth Of Cut At 90 Degrees: approx. 2-3/4" (70 mm)Maximum out rip: Max. 45 Degree Bevel Cut: approx. 2-1/2" (64 m . . .
|
 DELTA 15233 15 Production Drill Presses
Motor: 3 Phase, 3/4 HPMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and 3-Leg Overload Protection (LVC)Column Diameter: 2 3/4" (70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 . . .
|
 DELTA 15342 15 Production Drill Presses
Motor: 1 Phase, 3/4 HPMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and Overload Protection (LVC)Column Diameter: 2-3/4"(70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 x 356 . . .
|
 DELTA 32325 Line Boring Machines
Motor: 3/4 HP, 120V, 60 hz, 1 PhaseMotor Control: Column Diameter: N/ATable Tilt: Quill Stroke: N/AQuill Diameter: N/ASpeeds: 25/64"(10 mm)Table Size: 16" x 29-3/4" (406 x 756 mm)Spindle & Chuck Taper: N/AChuck to Table Capacity: N/AChuck to Base Capacity: N/ATable Insert: N/AKey Chuck Capacity: Height: 32-1/2" (826 mm)Length: 28-1/2" (724 mm)Width . . .
|
 DELTA 50850A 15 HP Dust Collector with Canister 1200 CFM
Motor: 1-1/2 HP, 3450 RPM, 120/240V (Wired 120V), 1 Phase, 60 hzMax. CFM: 1200Max. Static Pressure: 11.4 (inches of water)Impeller Diameter: Filter Bag Area: Canister: 33.1 square feetStandard Bag Filtration: 5 micronChip Bag Area: 6.3 cubic feetLength: 27" (686 mm)Width: 37" (940 mm)Height: 88" (2236 mm)Weight: 100 lbs (46 kg)Warranty: 2 Year Warr . . .
|
 DELTA 17959L 17 Laser Drill Press
Motor: 3/4 HPMotor Control: On/Off Push ButtonColumn Diameter: 3.15Table Tilt: 0-90 Left & Right; 0-45 ForwardQuill Stroke: 4-7/8" (124 mm)Quill Diameter: 1-3/4" (44 mm)Speeds: 215 - 2750 RPMTable Size: 18" x 14" (457 x 356 mm)Spindle & Chuck Taper: #2 Morse Taper; Jacobs 3Chuck to Table Capacity: 24-1/2" (622 mm)Chuck to Base Capacity: 44-1/2" (43 . . .
|
 DELTA JT360 Deluxe 6 Jointer
Motor: 3/4 HP, 120/240V, (wired 120V), 1 Phase, 60 hzCut Capacity - Width: 6-1/8" (156 mm)Cut Capacity - Depth: 1/8" (3 mm)Rabbeting Capacity: 1/2" (13 mm)Cutterhead Speed: 4,800 RPM, 14,400 CPMNumber of Knives: 3Cutterhead Diameter: 2-1/2" (64 mm)Table Size: 46" (1168 mm)Table Length of front table (Infeed): 22" (559 mm)Table Length of Rear Table . . .
|
 DELTA 33400 14 Radial Arm Saws
Motor: 3 HP, 1 Phase, 230 V, 60 hz, 3450 RPM, TEFC (totally enclosed, fan cooled) motorMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and Overload Protection (LVC)Blade Diameter: 14Arbor Size: 1" (25 mm)Crosscut Capacity (1" depth of cut): 29" (737 mm)Miter at 45° R & L (1" depth of cut): 22" (559 mm)Depth Of Cut At 90 Degree . . .
|
 DELTA GR350 8 Bench Grinder
Motor: 3 amp, 120V, 60 hz, 1 Phase, 3450 RPMMotor Control: On/Off lighted rocker switchWheel Diameter: 8" (203 mm)Wheel Type: Medium and Coarse Grinding WheelsWheel Face: 3/4" (19 mm)Wheel Hole: 5/8" (16 mm)Shaft Diameter: 5/8" (16 mm)Speeds: 3450 RPMGrit: 36G, 60GWidth: -Length: -Height: -Weight: 24 lbs (11 kg)Warranty: 2 Year Warranty . . .
|
 DELTA 37361 DJ 30 12 Jointer
Motor: 1 phase, 3 HP 3450 RPM, 230V, 60 hzCut Capacity - Width: 12" (304 mm)Cut Capacity - Depth: 3/4" (19 mm)Rabbeting Capacity: 3/4" (19 mm)Cutterhead Speed: 5,000 RPM; 15,000 CPMNumber of Knives: 3Cutterhead Diameter: 3-7/8" (98 mm)Table Size: 84" x 13" (2134 mm x 330 mm)Table Length of front table (Infeed): 41-1/2" (1054 mm)Table Length of Rear . . .
|
 DELTA 15231 15 Production Drill Presses
Motor: 1 Phase, 3/4 HPMotor Control: Push-Button Switch OnlyColumn Diameter: 2-3/4"(70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 x 356 mm) Production (overall): 15-1/2" x 21-1/2" (394 x 546 mm) . . .
|
 DELTA 15126 RAM TYPE RADIAL DRILL PRESS
Motor: 1/2 HP, 230/460V, 3 Phase, 60 hzMotor Control: Push button station, magnetic starter transformer and overload protection (LVC)Column Diameter: 3-3/4" (95mm)Table Tilt: 90°, 45° Left, vertical, 45° RightQuill Stroke: 6" (152 mm)Quill Diameter: 1-13/16" (46 mm)Speeds: 175 - 8200 RPMTable Size: 26" x 18" (660 x 457 mm)Spindle & Chuck Taper: Jac . . .
|
 DELTA 36851 Production Stock Feeder
Motor: 1 HP, 240V, 60 hz, 1 PhaseSpindle Diameter: -Speeds: 13, 26, 36, 72 FPMCapacity: -Table Size: -Table Height: -Fence Size: -Wheels: Diameter: 4-3/4" (120 mm) Width: 2-1/4" (57 mm) Roller Suspension: 3/4" (19 mm)Length: 18" (457 mm)Width: 11-1/2" (292 mm)Height: 18" (457 mm)Weight: 133 lbs (60 kg)Warranty: 2 Year Warranty . . .
|
 DELTA 15127 RAM TYPE RADIAL DRILL PRESS
Motor: 1/2 HP, 115/230V, 1 Phase, 60 hzMotor Control: Push button station, magnetic starter, transformer and 3-leg overload protection (LVC)Column Diameter: 3-3/4" (95mm)Table Tilt: 90°, 45° Left, vertical, 45° RightQuill Stroke: 6" (152 mm)Quill Diameter: 1-13/16" (46 mm)Speeds: With 1725 RPM Motor: 175 - 8200 RPMTable Size: 26" x 18" (660 x 457 m . . .
|
 DELTA 33420 18 Radial Arm Saw
Motor: 5 HP, 1 Phase, 230V, 60 hz, 3450 RPM, TEFC (totally enclosed, fan cooled) motorMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer & Overload Protection (LVC)Blade Diameter: 18Arbor Size: 1" (25 mm)Crosscut Capacity (1" depth of cut): 29" (737 mm)Miter at 45° R & L (1" depth of cut): 22" (559 mm)Depth Of Cut At 90 Degrees: . . .
|
 DELTA 20330 5 X 6 Horizontal Band Saw
Motor: 1/3 HP, 120V, 1 Phase, 60 hz, 1725 RPMMotor Control: On/off toggle switch with automatic shut-offBlade Width: 1/2" (13 mm)Blade Length: 64-1/2" (1638 mm)Cutting Heights: Speeds: 1725 RPMCapacity Blade to Frame: -Capacity Under Guide and Wheel: -Capacity: Diameter at 90°: 4" Diameter at 45°: 2-7/8" (73 mm) Rectangular at 90°: 4-1/2" x 6" R . . .
|
 DELTA 28682 18 WoodCutting Band Saw
Motor: 2 HP, 230V, 1 Phase, 60 hzMotor Control: Magnetic starterBlade Width: Min. 1/4"; Max. 1-1/2 (32 mm)Blade Length: Min: 135" (3429 mm); Max 137" (3480 mm); Standard: 136" (3454 mm)Cutting Heights: 12" (305 mm)Speeds: 2300/3250 SFPMCapacity Blade to Frame: 17-1/2" (445 mm)Capacity Under Guide and Wheel: 12Capacity: -Max Rip To Right Of Blade: 1 . . .
|
 DELTA 17950L 1612 Crosshair Laser Drill Press
Motor: 1/2 HP, 120V, 1Phase, 60 hz, 1720 RPMMotor Control: On/Off ToggleColumn Diameter: 3.15Table Tilt: 0-90 Left & Right; 0-45 ForwardQuill Stroke: 3-7/8Quill Diameter: 2Speeds: 250 - 3000 RPMTable Size: 14" x 18" (356 x 457 mm)Spindle & Chuck Taper: #2 Morse Taper; Jacobs 3Chuck to Table Capacity: Chuck to Base Capacity: Table Insert: Key Chuck . . .
|
 DELTA 22450 DC580 20 Planer
Motor: 3 Phase, 5 HP 220/440V (wired 220V), 60 hzMotor Control: 24V, low voltage magnetic controlMinimum Thickness Capacity: 11/16" (4 mm)Max. Width of Stock: 20" max. (508 mm)Max. Thickness of Stock: 8-5/8" (219 mm)Min. Length of Stock: 9" (229 mm)Number of Knives: 3Max. Depth of Cut: 3/16" max. (5 mm)Planing Width: 20" max. (508 mm)Cutterhead Dia . . .
|
 DELTA 15341 15 Production Drill Presses
Motor: 1 Phase, 3/4 HPMotor Control: Push-Button Switch OnlyColumn Diameter: 2-3/4"(70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 x 356 mm) Production (overall): 15-1/2" x 21-1/2" (394 x 546 mm) . . .
|
 DELTA 15263 15 Production Drill Presses
Motor: 3 Phase, 3/4 HPMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and 3-Leg Overload Protection (LVC)Column Diameter: 2-3/4"(70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 . . .
|
 DELTA 20950 20 VariableSpeed Drill Press
Motor: 1 HP, 120/240V, 11 Phase, 60 hzMotor Control: Push ButtonColumn Diameter: 3.15Table Tilt: 0-90 L & R; 0-45 FwdQuill Stroke: 6Quill Diameter: 2Speeds: Variable (200-250 RPM)Table Size: 24" x 14" (610 x 356 mm)Spindle & Chuck Taper: #2 Morse Taper; Jacobs 3Chuck to Table Capacity: 27-1/2" (699 mm)Chuck to Base Capacity: 47" (1194 mm)Table Inse . . .
|
 DELTA 36L31XU50 3 HP Left Tilt UNISAWreg with UNIFENCEreg
Motor: (TEFC) 3 HP, 230V , 60 hz, 1 phaseArbor Size: 5/8?? (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 4000 RPM (with 3450 RPM motor)Max Rip To Right Of Blade: 50" (1270 mm)Max Rip To Left Of Blade: 12" (305 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 16-13/ . . .
|
 DELTA 37380 8 Professional Jointer
Motor: 1-1/2 HP, 120/240V (wired 120V) 1 Phase, 60 hzCut Capacity - Width: 8" (203 mm)Cut Capacity - Depth: 1/2" (13 mm)Rabbeting Capacity: 1/2" (13 mm)Cutterhead Speed: 5,600 RPM; 16,800 CPMNumber of Knives: 3Cutterhead Diameter: 2-1/2" (64 mm)Table Size: 72-3/4" (1848 mm)Table Length of front table (Infeed): 35-1/4" (895 mm)Table Length of Rear T . . .
|
 DELTA 36977 10 Left Tilt CONTRACTORS SAWreg with DELTAreg T2 30 Fence Rail and Two Stamped Steel Ta
Motor: 1-1/2 HP, 115V/230V (wired 115V), 60 hzArbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 3000 RPMMax Rip To Right Of Blade: 30" (762 mm)Max Rip To Left Of Blade: 13-1/2" (343 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 17-1/2" (444 mm)Table . . .
|
 DELTA GR450 8 VS Grinder with Toolless Quick Change
Motor: 5 amp, 120V, 60 hz, 1725-3450 RPMMotor Control: Variable speedWheel Diameter: 8" x 1" thick (203 x 25 mm)Wheel Type: Friable Buffing WheelWheel Face: 1" (25 mm)Wheel Hole: 5/8" (16 mm)Shaft Diameter: 5/8" (16 mm)Speeds: 1725 - 3450 RPMGrit: 36G (gray), 60G (white)Width: -Length: -Height: -Weight: 48 lbs (22 kg)Warranty: 2 Year Warranty . . .
|
 DELTA 36717 10 Hybrid Saw w30 BIESEMEYERreg Commercial Fence System Rail and Table Board
Motor: 1-3/4 HP, 120V (240V capable), 60 hzArbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 3000 RPMMax Rip To Right Of Blade: 30" (762) 50" (1270 mmMax Rip To Left Of Blade: 13-1/2" (343 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 17-1/2" (444 . . .
|
 DELTA 37275X 6 Professional Jointer
Motor: 1 HP, 120/240V, 60 hz, 1 Phase, 3450 RPMCut Capacity - Width: 6-1/8" (156 mm)Cut Capacity - Depth: 1/8" (3 mm)Rabbeting Capacity: 1/2" (13 mm)Cutterhead Speed: 4,800 RPM; 14,400 CPMNumber of Knives: 3Cutterhead Diameter: 2-1/2" (64 mm)Table Size: 46" (1168 mm)Table Length of front table (Infeed): 22" (559 mm)Table Length of Rear Table (Outfe . . .
|
 DELTA 36979 10 LeftTilt Contractors Saw
Motor: 1-1/2 HP, 115V/230VArbor Size: 5/8?? (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 3000 RPMMax Rip To Right Of Blade: 30" (762 mm)Max Rip To Left Of Blade: 13-1/2" (343 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 17-1/2" (444 mm)Table in Front of Saw at . . .
|
 DELTA 36830LA 10 Unisawreg 3 HP Single Phase Left Tilt
Motor: 3 HP, 230V, 60 hz, 1 PhaseArbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 4,000 RPM (with 3450 RPM motor)Max Rip To Right Of Blade: 30" (762 mm)Max Rip To Left Of Blade: 12" (305 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 16-13/16" (427 . . .
|
 DELTA 36855 Production Stock Feeder
Motor: 1 HP, 240V, 60 Hz., 1 PhaseSpindle Diameter: -Speeds: 6.5, 13, 18, 22, 36, 43, 55, 108 FPMCapacity: -Table Size: -Table Height: -Fence Size: -Wheels: Diameter: 4-3/4" (120 mm) Width: 2-1/4" (57 mm) Roller Suspension: 3/4" (19 mm)Length: 23-1/4" (590 mm)Width: 11-1/2" (292 mm)Height: 18-1/2" (469 mm)Weight: 148 lbs (67 kg)Warranty: 2 Year W . . .
|
 DELTA 31396 Oscillating Edge Sander with Spindle Sanding Attachment
Motor: 3 HP, 220V, 1 Phase, 1720 RPMAbbrasive Belt Size: 6" x 108" (152 x 2743 mm)Disc Diameter: N/ASpeeds: Belt speed: 3150 FPMTable Size: Front Table Size: 35-3/8" x 12" (899 x 305 mm) Auxiliary Table Size: 11-3/8" x 8-7/8" (289 x 225 mm)Miter Gauge Groove: 3/8" x 3/4Platen Tilting: 0 - 90°Table Tilt: 0Dust Port Diameter: 4" (102 mm)Sanding Drum . . .
|
 DELTA 36831LA 10 Unisawreg 3HP Single Phase Left Tilt
Motor: 3 HP, 230V, 60 hz, 1 PhaseArbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 4000 RPM (with 3450) motorMax Rip To Right Of Blade: With UNIFENCE® Saw Guide or BIESEMEYER® Commercial Saw Fence System: 50" (1270 mm)Max Rip To Left Of Blade: With UNIFENCE® Saw Guide: 15-1/2" (394 mm) With BIESEMEYER® Fence: 12" (305 mm)Depth Of Cu . . .
|
 DELTA GR275 6 Variable Speed Grinder wToolless Quick Change
Motor: 2.0 amp, 120V, 60 hz, 1 Phase, 2000-3450 RPMMotor Control: On/Off switch with speed controlWheel Diameter: 6" (152 mm)Wheel Type: White friable wheel for sharpening Grinding wheelWheel Face: 3/4" (19 mm)Wheel Hole: 1/2" (13 mm)Shaft Diameter: 1/2" (13 mm)Speeds: 2000 - 3450 RPMGrit: 36G (gray), 60G (white)Width: -Length: -Height: -Weight: 2 . . .
|
 DELTA 36L51XBC50 5 HP Left Tilt UNISAWreg with BIESEMEYERreg Fence
Motor: (TEFC) 5 HP, 230V , 60 hz, 1 phaseArbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 4000 RPM (with 3450 RPM motor)Max Rip To Right Of Blade: 50" (1270 mm)Max Rip To Left Of Blade: 12" (305 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 16-13/1 . . .
|
 DELTA 36850 Production Stock Feeder
Motor: 1 HP, 120V, 60 hz, 1 PhaseSpindle Diameter: -Speeds: 13, 26, 36, 72 FPMCapacity: -Table Size: -Table Height: -Fence Size: -Wheels: Diameter: 3-1/8" (79 mm) 1-3/16" (30 mm) 3/4" (19 mm)Length: 12" (304 mm)Width: 8-1/2" (215 mm)Height: 13-1/2" (342 mm)Weight: 70 lbs (31 kg)Warranty: 2 Year Warranty . . .
|
 DELTA AP300 Portable Dust Collector
Motor: 3450 RPM, 3/4 HP, 120/240V (wired 120V), 9/4.5 amp, 60 hz, 1 PhaseMax. CFM: 500 (15.5 cmm)Max. Static Pressure: 5.3 in waterImpeller Diameter: Filter Bag Area: Standard Bag Filtration: 30 micronChip Bag Area: Length: 38" (965 mm)Width: 21" (533 mm)Height: 38" (965 mm)Weight: 50 lbs (23 kg)Warranty: 2 Year Warranty . . .
|
 DELTA 22610 RC63D 24 34 X 9 38 Planer
Motor: 10 HP, 200-220/440V (wired 200-220V), 3 PhaseMotor Control: 24V, low voltage controlMinimum Thickness Capacity: 1/8" (3 mm)Max. Width of Stock: 24.8" (630 mm)Max. Thickness of Stock: 9.38" (238 mm)Min. Length of Stock: 11" (279 mm)Number of Knives: 4Max. Depth of Cut: .39" (10 mm)Planing Width: 1/8" (3 mm)Cutterhead Diameter: 4.72" (120 mm)C . . .
|
 DELTA AP200 18 HP Portable Air Cleaner 850CFM
Motor: 1/8 HP, 1050 RPM, 120V, 1 Phase, 60 hzMax. CFM: 850 CFM (24 cmm)Filter Cycle: 20' x 20' x 8' room, 16 times per hourStandard Bag Filtration: Outer filter: 5 microns Inner filter: 1 micronLength: 30" (762 mm)Width: 24" (610 mm)Height: 12" (305 mm)Weight: 50 lbs. (23 kg)Warranty: 2 Year Warranty . . .
|
 DELTA 14651 Deluxe Mortiser
Motor: 1/2 HP, 120V, 60 hz, 1 Phase induction motor 1750 RPMMotor Control: Push button staion; magnetic starter, transformer and 3-leg overload protection (LVC).Column Diameter: 3-3/4" (95 mm)Table Tilt: 90°, 45° Left, vertical, 45° RightQuill Stroke: 6" (152 mm)Quill Diameter: 1-13/16 (46 mm)Speeds: Table Size: 16-1/4" x 13-1/2" (413 x 343 mm)Spin . . .
|
 DELTA AP100 Ambient Air Cleaner wWork Light
Motor: 3.0 amps, 120V, 1 Phase, 60 hzMax. CFM: 450 CFMFilter Cycle: 20' x 20' x 8' room, 8 times per hourStandard Bag Filtration: 5 micronLength: 23Width: 23Height: 20.5Weight: 40Warranty: 2 Year Warranty . . .
|
 DELTA 33890 12 Radial Arm Saws
Motor: 2 HP, 230V, (wired 230V), 60 hz, 1 PhaseMotor Control: On-off key lock switchBlade Diameter: (supplied): 12" (305 mm)Arbor Size: 5/8" -12 LH. Acme (16 mm)Crosscut Capacity (1" depth of cut): 14-3/8" (365 mm)Miter at 45° R & L (1" depth of cut): 2-1/2Depth Of Cut At 90 Degrees: 3-3/4Maximum out rip: 24-1/4" (616 mm)Max. 45 Degree Bevel Cut: 1 . . .
|
 DELTA 15333 15 Production Drill Presses
Motor: 3 phase, 3/4 HPMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer and 3-Leg Overload Protection (LVC)Column Diameter: 2-3/4" (70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 . . .
|
 DELTA 28206 14 Band Saw with 1HP Motor Enclosed Stand
Motor: 1 HP, 120/240V (wired 120V), 1 Phase 60 hzMotor Control: Blade Width: Max. 3/4" (19 mm)Blade Length: Min. 91-1/2" (2324 mm)/ Max. 94" (2388 mm)/ Standard: 91-1/2" (2324 mm)Cutting Heights: -Speeds: 2500/3300 SFPM (762/1006 SMPM)Capacity Blade to Frame: 13-3/4" (349 mm)Capacity Under Guide and Wheel: 6-1/4" (159 mm); W/ 28-984 height attach: . . .
|
 DELTA 23725 SlowSpeed Bench Grinder
Motor: 3/4 HP, 8 amp, 120V, 60 hz, 1 Phase, 1725 RPMMotor Control: Toggle switchWheel Diameter: 8" (203 mm)Wheel Type: Friable, aluminum oxide wheelWheel Face: 1" (25 mm)Wheel Hole: 1" (25 mm)Shaft Diameter: 5/8" (16 mm)Speeds: 1725 RPMGrit: 120 (white L) 60 (gray R)Width: -Length: -Height: -Weight: 100 lbs (45 Kg)Warranty: 2 Year Warranty . . .
|
 DELTA 36715 10 Hybrid Saw with T2 30 Fence and Rail
Motor: 1-3/4 HP, 120V, 60 hz (240V capable)Arbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 3000 RPMMax Rip To Right Of Blade: 30" (762 mm) 50" (1270 mm)Max Rip To Left Of Blade: 13-1/2" (343 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 17-1/2" ( . . .
|
 DELTA 36790 1416 Tilting Arbor Saw
Motor: (TEFC) 7-1/2 HP, 200/440V (wired 200-220V), 3 Phase, 60 hzArbor Size: Up to 16" (406.4 mm)Blade Diameter: 10" (254 mm)Blade Speed: 3,000-4,500 RPMMax Rip To Right Of Blade: 51-3/16" (1300 mm)Max Rip To Left Of Blade: -Depth Of Cut At 45 Degrees: With 14" blade: 3-1/8" (79 mm) With 16" blade: 4-1/8" (105 mm)Depth Of Cut At 90 Degrees: With 1 . . .
|
 DELTA 15331 15 Production Drill Presses
Motor: 3 Phase, 3/4 HPMotor Control: Push-Button Switch OnlyColumn Diameter: 2 3/4" (70 mm)Table Tilt: 90° L and RQuill Stroke: 6" (152 mm)Quill Diameter: 2" (51 mm)Speeds: With 1725 RPM motor: 450 to 4700 RPM With 1140 RPM motor: 300 to 3100 RPMTable Size: Standard: 11" x 14" (279 x 356 mm) Production (overall): 15-1/2" x 21-1/2" (394 x 546 mm) . . .
|
 DELTA 50762 3 HP Dust Collector 2700 CFM
Motor: 3 HP, 3450 RPM, 230/460V, (Wired 230V), 3 Phase, 60 hzMax. CFM: 2700Max. Static Pressure: 10.5 (inches of water)Impeller Diameter: 13" (330 mm)Filter Bag Area: 57.2 square feet, 5.3 square metersStandard Bag Filtration: 1 micronChip Bag Area: 7.6 cubic feet, 218 litersLength: 66" (1676 mm)Width: 23" (584 mm)Height: 110" (2794 mm)Weight: 186 . . .
|
 DELTA 33410 16 Radial Arm Saw
Motor: 3 HP, 1 Phase, 230V, 60 hz, 3450 RPM, TEFC (totally enclosed, fan cooled) motorMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer & Overload Protection (LVC)Blade Diameter: 16Arbor Size: 1" (25 mm)Crosscut Capacity (1" depth of cut): 29" (737 mm)Miter at 45° R & L (1" depth of cut): 22" (559 mm)Depth Of Cut At 90 Degrees: . . .
|
 DELTA 32350 Horizontal Boring Machine
Motor: 1HP, 3450 rpm, 115/230V, 60 hz, 1 PhaseMotor Control: Column Diameter: N/ATable Tilt: Quill Stroke: N/AQuill Diameter: N/ASpeeds: Table Size: 15-3/4" x 9-7/8" (400 x 251 mm)Spindle & Chuck Taper: N/AChuck to Table Capacity: N/AChuck to Base Capacity: N/ATable Insert: Key Chuck Capacity: Height: 48" (1219 mm)Length: 37-1/2" (953 mm)Width: 15- . . .
|
 DELTA 50875 3Speed Ambient Air Cleaner
Motor: 1/5 HP, 120V, 1 Phase, 60 hzMax. CFM: 540, 730, 1200 CFMFilter Cycle: 20' x 20' x 8' room, 10, 14, 22 times/hourStandard Bag Filtration: Outer Filter: 5 micron electrostatic filter Inner filter: 1 micronLength: 30" (762 mm)Width: 24" (610 mm)Height: 12" (305 mm)Weight: 50 lbs. (23kg)Warranty: 2 Year Warranty . . .
|
 DELTA 22451 DC580 20 Planer
Motor: 1 Phase, 5 HP, 220V 60 hzMotor Control: 24V, low voltage magnetic controlMinimum Thickness Capacity: 11/16" (4 mm)Max. Width of Stock: 20" max (508 mm)Max. Thickness of Stock: 8-5/8" max (219 mm)Min. Length of Stock: 9" (229 mm)Number of Knives: 3Max. Depth of Cut: 1/8" max. (3 mm)Planing Width: 20" max. (508 mm)Cutterhead Diameter: 3-1/8" ( . . .
|
 DELTA 36716 10 Hybrid Saw w30 DELTAreg UNIFENCEreg Rail and Table Board
Motor: 1-3/4 HP, 120V, 60 hz (240V capable)Arbor Size: 5/8" (16 mm)Blade Diameter: 10" (254 mm)Blade Speed: 3000 RPMMax Rip To Right Of Blade: 30" (762); 50" (1270 mm)Max Rip To Left Of Blade: 13-1/2" (343 mm)Depth Of Cut At 45 Degrees: 2-1/8" (54 mm)Depth Of Cut At 90 Degrees: 3-1/8" (79 mm)Distance, front of table to center of blade: 17-1/2" (444 . . .
|
 DELTA 43460 HeavyDuty Wood Shaper
Motor: 5 HP, 200-230/460V, 3 phase, 60 hz (wired200)Spindle Diameter: 1-1/4Speeds: 7,000 & 10,000 RPMCapacity: 5/1/4" (133 mm)Table Size: 40" x 27" (1016 x 686 mm)Table Height: 34" (864 mm)Fence Size: Each side 16-1/2" x 1-3/8" x 5" (418 x 3 x 127 mm)Wheels: -Length: 27" (686 mm)Width: 40" (1016 mm)Height: 50" (1270 mm)Weight: 456 lbs (207 kg)Warra . . .
|
 DELTA 43791 5Speed Wood Shaper
Motor: 7-1/2 HP, 200-220/440V (wired 200-220V), 3450 RPM, 60 hz, 3 Phase For 440V, 3 Phase operation, you must order Control Part No. 1348629Spindle Diameter: 3/4" and 1-1/4Speeds: 3000, 4000, 6000, 800 & 10,000 RPMCapacity: 3/4" Spindle: 9" (229 mm) 1-1/4 Spindle: 4-7/8" (124 mm)Table Size: 31-3/4" x 39-5/8" (806 x 1007 mm)Table Height: 34-1/2" . . .
|
 DELTA 33411 16 Radial Arm Saws
Motor: 5 HP, 1 Phase, 230V/460V wired 230V), 60 hz., 3450 RPM, TEFC (totally enclosed, fan cooled) motorMotor Control: 24V Push-Button Station, Magnetic Starter, Transformer & Overload Protection (LVC)Blade Diameter: 16Arbor Size: 1" (25 mm)Crosscut Capacity (1" depth of cut): 29" (737 mm)Miter at 45° R & L (1" depth of cut): 22" (559 mm)Depth Of C . . .
|
 DELTA 37365X 8 Precision Jointer DJ20
Motor: 1-1/2 HP, 120/240V (wired 240V), 60 hz, 1 Phase TEFC, 3450 RPMCut Capacity - Width: 8" (203 mm)Cut Capacity - Depth: 5/8" (16 mm)Rabbeting Capacity: 5/8" (16 mm)Cutterhead Speed: 5,500 RPM; 16,500 CPMNumber of Knives: 3Cutterhead Diameter: 3-3/8" (86 mm)Table Size: 76-1/2" (1943 mm)Table Length of front table (Infeed): 42" (1067 mm)Table Len . . .
|
 DELTA 37360 DJ 30 12 Jointer
Motor: 3 Phase, 3 HP, 3450 RPM, 220-240/460V (Wired 220V), 60 hzCut Capacity - Width: 12" (304 mm)Cut Capacity - Depth: 3/4" (19 mm)Rabbeting Capacity: 3/4" (19 mm)Cutterhead Speed: 5,000 RPM, 15,000 CPMNumber of Knives: 3Cutterhead Diameter: 3-7/8" (98 mm)Table Size: 84" x 13" (2134 mm x 330 mm)Table Length of front |
